10/29/2022 0 Comments Os/9 emulator -mac -macos -macos9![]() ![]()
OS/9 EMULATOR MAC MACOS MACOS9 WINDOWS 10Before I beginīefore I get started, I need to point out that the Android emulator currently only works on the Windows 10 version of Hyper-V. As such, I thought that it might be fun to work through the setup. From the management station or NMS, use the SSH or Telnet application to connect to the managed device.One of the announcements that caught my attention at this year’s Microsoft Build conference was that it there is now an Android emulator that has been specifically designed to work with Hyper-V. OS/9 EMULATOR MAC MACOS MACOS9 PASSWORDCheck the documentation for the switches you are using to find the default protocols that are enabled and the ID and password credentials for logging in. For example, switches running OS10EE have SSH enabled and telnet disabled by default. While some switches have SSH enabled by default (with Telnet disabled), others have Telnet enabled by default. Show port configuration: OS10(conf-if-eth1/1/48)# show configuration OS10(config)# interface range ethernet 1/1/1-1/1/4 OS10(config)# description “server connections” OS10(conf-if-eth1/1/48)# switchport trunk allowed vlan 10 ![]() OS10(conf-if-eth1/1/48)# switchport mode trunk OS10(config)# description “upstream network” OS10(config)# description “Management VLAN” Apply an IP address to the VLAN and add the VLAN to the ports. Replace the IP address with an available one for your network.Ĭonfigure the management VLAN for upstream and server connections VLAN 10 is used for upstream and server management in this example. OS/9 EMULATOR MAC MACOS MACOS9 SERIESThe commands in this section describe the steps needed to configure the management VLAN port on a Dell EMC PowerSwitch series switch with OS10EE installed. OS9(conf-if-vl-10)# tagged tengigabitethernet 1/1-1/4,1/48 OS10EE configuration OS9(conf-if-vl-10)# description Management VLAN Note: Replace the IP address and VLAN ID shown to match your network. Tag the ports that will be part of the management VLAN. Provide an interface description and apply an IP address. OS9(conf-if-te-1/48)# description server connectionsĬonfigure the VLAN for connections to the upstream and server connections port 1/48 is used for upstream and ports 1/1-1/4 are used for server connections in this example. OS9(conf)# interface range tengigabitethernet 1/1-1/4 OS9(conf-if-te-1/48)# description upstream network OS9(conf)#interface tengigabitethernet 1/48 Provide an interface description, use portmode hybrid to allow tagged and un-tagged frames, and configure ports as layer 2 switchport using the switchport command. In this example port 1/48 is used for upstream and ports 1/1-1/4 are used for server connections. OS9(conf)# no ip telnet enable (optional)Ĭonfigure the interfaces for the upstream and server connections. OS9(conf)# username admin password admin privilege 15 For a more secure connection, SSH is enabled and Telnet is disabled. OS/9 EMULATOR MAC MACOS MACOS9 HOW TOThe commands in this section show how to configure the management VLAN on a Dell EMC PowerSwitch series switch with OS9 installed. Consult the documentation included with the switch for the specific commands to use. Note: While the steps in this document were validated using the specified Dell EMC PowerSwitch series of switches and operating systems, they may be used for other Dell EMC PowerSwitch models using the same networking operating system version or later assuming the switch has the available port numbers, speeds, and types. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |